OC
UnclassifiedCooling
What This Code Means
Common fault/prealarm line 1 activated; Common fault/prealarm line 2 activated; Fault lamp activated (activelow); Common fault/prealarm line activated; Fault lamp activated; Shutdown occurs if the engine coolant temperature exceeds the maximum temperature for more than 5 seconds; Shutdown occurs if a low oil pressure condition exists for more than 5 seconds; Shutdown occurs after 3 unsuccessful starting attempts; No engine rotation is sensed during cranking
Possible Causes
- •3 unsuccessful starting attempts
- •AHET (Anticipatory high engine temperature) fault
- •ALOP (Anticipatory low oil pressure) fault
- •AUX
- •AUX (Auxiliary) fault
- •AUX Fault
- •AUX Fault (Auxiliary)
- •AUX condition
- •AUX faults
- •Anticipatory high engine temperature (AHET) fault
- •Anticipatory high engine temperature (AHET) fault (Terminal 40)
- •Anticipatory high engine temperature (AHET) prealarm
- •Anticipatory high engine temperature fault (AHET, terminal 40)
- •Anticipatory low oil pressure (ALOP) fault
- •Anticipatory low oil pressure (ALOP) fault (Terminal 41)
- •Anticipatory low oil pressure (ALOP) prealarm
- •Anticipatory low oil pressure fault (ALOP, terminal 41)
- •Auxiliary (AUX)
- •Auxiliary (AUX) Fault
- •Auxiliary (AUX) fault
- •Auxiliary (AUX) fault (Terminal 26)
- •Auxiliary (AUX) faults
- •Auxiliary fault (AUX)
- •Auxiliary fault (AUX, terminal 26)
- •Battery Charger Fault (BATTERYCH.FAULT)
- •Battery issue
- •Batterycharger fault
- •Batterychargerfault
- •Blocked air inlets and exhaust outlets
- •ES (Emergency stop) fault
- •Emergency Stop (E.STOP)
- •Engine fails to start within the total allocated cyclic cranking time
- •Engine fault (OC, OS, HWT, LOP, or LWL)
- •Engine faults (OC, OS, HWT, LOP, LWL)
- •Failure to receive a successful run signal within 30 seconds of total engine cranking time
- •Fault shutdown condition (OC, OS, HWT, LOP, or LWL)
- •Faulty fuel supply
- •Faulty or discharged battery
- •Faulty spark plug
- •Fuel supply issue
- •HET (High engine temperature) fault
- •HET Fault
- •HET Fault (High Engine Temperature)
- •HET condition
- •High Engine Temperature (HET)
- •High Engine Temperature (HET) Fault
- •High Engine Temperature fault (HET)
- •High engine temperature (HET) fault
- •High engine temperature (HET) fault (Terminal 36)
- •High engine temperature fault (HET, terminal 36)
- •K5 relay energized closing contacts across remote start leads (RUN LATCH)
- •LF (Low fuel) fault
- •LOP (Low oil pressure) fault
- •LOP Fault
- •LOP Fault (Low Oil Pressure)
- •LOP condition
- •LWT (Low water temperature) fault
- •LWT Fault
- •LWT Fault (Low Water Temperature)
- •LWT condition
- •Leaks in the lubrication system
- •Loose connections
- •Low Battery (LOWBATT.)
- •Low Fuel (LOWFUEL)
- •Low Oil (LO)
- •Low Oil Pressure (LOP)
- •Low Oil Pressure (LOP) Fault
- •Low Oil Pressure fault (LOP)
- •Low Water Temperature (LWT)
- •Low Water Temperature (LWT) Fault
- •Low Water Temperature fault (LWT)
- •Low Water Temperature/Level (LWT)
- •Low battery volts
- •Low fuel
- •Low fuel (LF) fault
- •Low fuel (LF) fault (Terminal 63)
- •Low fuel fault (LF, terminal 63)
- •Low oil level
- •Low oil pressure (LOP) fault
- •Low oil pressure (LOP) fault (Terminal 38)
- •Low oil pressure fault (LOP, terminal 38)
- •Low water temperature (L WT) fault
- •Low water temperature (LWT) fault
- •Low water temperature (LWT) fault (Terminal 35)
- •Low water temperature fault (L WT, terminal 35)
- •No engine rotation during cranking
- •No engine rotation sensed during cranking
- •OC (Overcrank) fault
- •OC Fault
- •OC Fault (Overcrank)
- •OC condition
- •OC, AUX, LWT, HET, LOP, OS, AHET, ALOP, and LF faults
- •OS (Overspeed) fault
- •OS Fault
- •OS Fault (Overspeed)
- •OS condition
- •Overcrank (OC)
- •Overcrank (OC) Fault
- •Overcrank (OC) fault
- •Overcrank (OC) fault (Terminal 12)
- •Overcrank (oC)
- •Overcrank fault (OC)
- •Overcrank fault (OC, terminal 12)
- •Overspeed (OS)
- •Overspeed (OS) Fault
- •Overspeed (OS) fault
- •Overspeed (OS) fault (Terminal 39)
- •Overspeed fault (OS)
- •Overspeed fault (OS, terminal 39)
- •Run latch (K5 relay) preventing remote reset
- •SO
- •Spark plug issue
- •Three unsuccessful starting attempts
- •Unit shutdown triggered by a fault condition (OC, OS, HWT, LOP, LWL)
- •Unsuccessful engine starting attempts
Suggested Actions
- 1Activate audiovisual alarm or common fault relay
- 2Check battery
- 3Check for blocked air inlets and exhaust outlets
- 4Check for leaks in the lubrication system
- 5Check for loose connections
- 6Check spark plug
- 7Check the battery
- 8Check the fuel supply
- 9Check the fuel supply, spark plug, and battery
- 10Check the oil level and add oil if the level is low
- 11Check the oil level at the engine
- 12Check the spark plug
- 13Connect A/V Alarm or Common Fault Relay Kit
- 14Connect A/V Alarm or Common Fault Relay Kit to terminal TB1-32
- 15Connect AV Alarm or Common Fault Relay Kit
- 16Connect a remote annunciator and/or audiovisual alarm kit as an indicator with a dry contact kit connected to controller terminal strip TB1.
- 17Connect battery charger alarm contact to TB1-61 to activate fault lamp (activelow) (if used).
- 18Connect battery charger alarm contact to TB1-62
- 19Connect battery charger alarm contact to TB1-62 to activate fault lamp (activelow) (if used).
- 20Connect batterycharger alarm contact to TB1-61
- 21Connect fuel level sensor to TB1-63
- 22Connect fuel level sensor to TB1-63 to activate fault lamp (activelow) (if used).
- 23Contact an authorized Kohler distributor/dealer for service if problem continues
- 24Contact an authorized distributor/dealer for service
- 25Contact an authorized distributor/dealer for service if problem continues
- 26Correct the cause of failure
- 27Operator must reset the fault at the generator by placing switch in OFF position
- 28Place selector switch in OFF/RESET position at the generator to reset the fault
- 29Place selector switch in OFF/RESET position at the generator to reset the fault logic
- 30Place the selector switch in the 'Reset/Off' position prior to attempting another start cycle
- 31Reset at the generator controller by moving the Start / Stop switch to the OFF / RESET position
- 32Reset fault shutdown condition using the generator set master switch (OFF/RESET)
- 33Reset the controller
- 34Use a remote annunciator and/or A/V alarm kit as an indicator with a dry contact kit connected to controller terminal strip TB1
- 35Use a remote annunciator and/or audiovisual alarm kit as an indicator with a dry contact kit connected to controller terminal strip TB1
Related Rehlko Fault Codes
ASK RUDY ABOUT THIS FAULT
Get a diagnosis walkthrough for OC on your specific Rehlko unit — cited to the OEM manual, not a forum guess.
GET THE ANSWER
Free account required — we'll bring your question with you.